Job Description

Aerotek is hiring Electricians!

This is a travel position - contractor must use their own vehicle.

Work is done in Longview, Marshall, San Angelo, Cisco, Texas.

Tools are required.

Summary: Electricians work as part of the maintenance team to support the maintenance, troubleshooting, and repair of the mechanical and electronic equipment and components used.

Essential Duties and Responsibilities:

• Must provide their own basic tools and understand their proper use (list will be provided.) \xe2\x80\xa2 Understand the use of hand and power tools to do electrical repair work.

• Must have a basic understanding of how to read and understand schematics.

• Must perform proper and safe cable routing.

• Component identification and basic understanding of the operation such as, relays, circuit breakers, fuses, inverters, rectifiers, and PLC\'s

• Must be able to properly use various testers, such as multimeters, meggers, oscilloscope, along with other hand tools to complete a job.

• Complete preventive maintenance tasks as scheduled, and document finished work

• Troubleshoot mechanical equipment, PLC\'s and ladder diagrams, AC and DC circuits, electrical sensors and switches, motor controls and, safety circuits

• Assists in routine planned maintenance and emergency repairs of plant equipment including conveyors, bucket elevators, and washing/drying equipment

• Be able to exercise the proper use of wiring techniques for 12-volt DC, 24-volt DC, 120-volt DC, 120-volt AC, 240-volt AC, 480-volt AC, 600-volt AC and 13.8 kV AC, single and three-phase.

• Thorough understanding of mechanical, hydraulic, pneumatic and electrical systems

• Strong understanding of software utilized within programmable logic control (PLC) systems. GE Drive Coach, Woodward, Danfoss, LS H Series, Toshiba \xe2\x80\xa2 Design, plan, install and maintain industrial control equipment and instrumentation such as loop controller, variable frequency drives, solid state reduced voltage starters, level controls, ethernet motor controls centers, belt scales, and control panels

• Installation, modification and repair of automated industrial control equipment

Supervisory Responsibilities:

• No direct supervisory responsibility but may assist with training new employees to the company.

Work Schedule

• Ability to work a rotational schedule including 14 days on duty and 7 days off duty however, schedule is subject to change and fluctuate due to company needs

o Schedules include working day shift, night shift, weekends, holidays, etc.

• Willingness to workdays off if needed

• Willingness to travel out of state and to other Districts as necessary

• Must have a smartphone to be able to utilize when needed and be available when contacted

Education and/or Experience

• High School Diploma or GED.

• First Aid/CPR Training and Safe Land/PEC Certified preferred.

• 1-3 years in Hydraulic fracturing or oilfield operating company.

• Basic knowledge of frac equipment with 1-2 years\' experience in Electrical field with knowledge of A/C power and A/C motors.

• Must possess a Journeyman Electrician License issued by the state of the district advertising the opening. In the absence of a license, must have minimum number of hours required by the State in either electrical work or classroom instruction to obtain the license.

• Able to read, speak, and comprehend effectively and write sufficiently to be understood by employees, peers, and customers in English.

• Must have and maintain a driving record acceptable to the Company and ProFrac Services auto insurance company.

Physical Requirements

• Ability to successfully pass a ProFrac Services pre-employment physical and drug screen.

• Standing: 6-12 hours per day

• Sitting: 6-12 hours per day

• Driving: 1-5 hours per day

• Climbing: Ability to climb ladders up to 25 feet to work platforms

• Lifting: Up to 40lbs, additional weight may be required with a second individual assisting.

• Ability to wear a full and/or half face respirator.

• Ability to wear FR (Flame Resistant) uniforms including pants, shirts, and/or coveralls.

Tools Needed

Electricians will be required to have and maintain the below required list of tools:

Multimeter Good for 1000 volt AC and DC

Insulated Screwdrivers

Standard Screwdriver Set

Insulated Line Plyers

Insulated Side cutters

Insulated Needle Nose plyers

6" Crescent Wrench

10 or 12 " Crescent Wrench

1/4 " Socket Set

Wrench Set Up to "

3/8 " socket set

3/8 Extensions to Reach 18"

Standard Allen Wrenches to 5/8"

Metric Allen Wrenches

Strippers

Channel locks

Headlamp

Crimpers

Flashlight

Tool storage of your choice

Basic file set

Tape Measure

Company Provided 1000 volt Gloves W/Protectors

Company Provided LOTO

About Aerotek:

We know that a company\'s success starts with its employees. We also know that an individual\'s success starts with the right career opportunity. As a Best of Staffing Client and Talent leader, Aerotek\'s people-focused approach yields competitive advantage for our clients and rewarding careers for our contract employees. Since 1983, Aerotek has grown to become a leader in recruiting and staffing services. With more than 250 non-franchised offices, Aerotek\'s 8,000 internal employees serve more than 300,000 contract employees and 18,000 clients every year. Aerotek is an Allegis Group company, the global leader in talent solutions. Learn more at

The company is an equal opportunity employer and will consider all applications without regards to race, sex, age, color, religion, national origin, veteran status, disability, sexual orientation, gender identity, genetic information or any characteristic protected by law.

Aerotek